Practice with NSE7_SDW-7.2 Dumps for NSE 7 Network Security Architect Certified Exam Questions & Answer
REAL NSE7_SDW-7.2 Exam Questions With 100% Refund Guarantee
NEW QUESTION # 18
Refer to the exhibits.
Exhibit A
Exhibit B
Exhibit A shows an SD-WAN event log and exhibit B shows the member status and the SD-WAN rule configuration.
Based on the exhibits, which two statements are correct? (Choose two.)
- A. SD-WAN rule ID 1 is set to lowest cost (SLA) mode.
- B. Port2 has a lower latency than port1.
- C. FortiGate updated the outgoing interface list on the rule so it prefers port2.
- D. Port2 has the highest member priority.
Answer: B,C
NEW QUESTION # 19
Refer to the exhibit.
FortiGate has multiple dial-up VPN interfaces incoming on port1 that match only FIRST_VPN.
Which two configuration changes must be made to both IPsec VPN interfaces to allow incoming connections to match all possible IPsec dial-up interfaces? (Choose two.)
- A. Use different proposals are used between the interfaces.
- B. Configure the IKE mode to be aggressive mode.
- C. Specify a unique peer ID for each dial-up VPN interface.
- D. Use unique Diffie Hellman groups on each VPN interface.
Answer: B,C
NEW QUESTION # 20
Refer to the exhibit.
Based on the output shown in the exhibit, which two criteria on the SD-WAN member configuration can be used to select an outgoing interface in an SD-WAN rule? (Choose two.)
- A. Set priority 10.
- B. Set source 100.64.1.1.
- C. Set cost 15.
- D. Set load-balance-mode source-ip-ip-based.
Answer: A,C
NEW QUESTION # 21
Refer to the exhibit.
Based on the exhibit, which two actions does FortiGate perform on sessions after a firewall policy change?
(Choose two.)
- A. FortiGate terminates the old sessions.
- B. FortiGate evaluates new sessions.
- C. FortiGate flushes all sessions.
- D. FortiGate does not change existing sessions.
Answer: B,D
Explanation:
Explanation
FortiGate not to flag existing impacted session as dirty by setting firewall-session-dirty to check new. The
results is that FortiGate evaluates only new session against the new firewall policy.
NEW QUESTION # 22
Refer to the exhibit.
The exhibit shows the BGP configuration on the hub in a hub-and-spoke topology. The administrator wants BGP to advertise prefixes from spokes to other spokes over the IPsec overlays, including additional paths. However, when looking at the spoke routing table, the administrator does not see the prefixes from other spokes and the additional paths.
Based on the exhibit, which three settings must the administrator configure inside each BGP neighbor group so spokes can learn other spokes prefixes and their additional paths? (Choose three.)
- A. Enable soft-reconfiguration
- B. Set adv-additional-path to the number of additional paths to advertise
- C. Enable route-reflector-client
- D. Set advertisement-interval to the number of additional paths to advertise
- E. Set additional-path to send
Answer: B,C,E
NEW QUESTION # 23
Refer to the exhibits.

Exhibit A shows the SD-WAN rule status and the learned BGP routes with community 65000:10.
Exhibit B shows the SD-WAN rule configuration, the BGP neighbor configuration, and the route map
configuration.
The administrator wants to steer corporate traffic using routes tags in the SD-WAN rule ID 1.
However, the administrator observes that the corporate traffic does not match the SD-WAN rule ID 1.
Based on the exhibits, which configuration change is required to fix issue?
- A. In SD-WAN rule ID 1, change the destination to use ISDB entries.
- B. In the BGP neighbor configuration, apply the route map dcl-lab-rm in the outbound direction.
- C. In the dcl-lab-rm route map configuration, set set-route-tag to 10.
- D. In the dcl-lab-rm route map configuration, unset match-community.
Answer: B
NEW QUESTION # 24
Which statement about using BGP for ADVPN is true?
- A. You must configure AS path prepending.
- B. You must configure BGP communities.
- C. You must use BGP to route traffic for both overlay and underlay links.
- D. IBGP is preferred over EBGP, because IBGP preserves next hop information.
Answer: D
Explanation:
ADVPN is a technology that allows dynamic creation of IPsec tunnels between branch sites without requiring pre-configured policies or keys. BGP is a routing protocol that can be used to exchange routes between ADVPN peers. IBGP is a type of BGP that runs between routers in the same autonomous system (AS), while EBGP is a type of BGP that runs between routers in different ASes. IBGP is preferred over EBGP for ADVPN, because IBGP preserves the next hop information of the routes, which is needed to establish the IPsec tunnels. EBGP changes the next hop information to the EBGP peer address, which may not be reachable by the ADVPN peers. Therefore, using IBGP for ADVPN avoids the need to configure additional static routes or redistribute routes between BGP and another routing protocol. Reference = ADVPN with BGP as the routing protocol, ADVPN, SD-WAN self-healing with BGP, Technical Tip: ADVPN with BGP as the routing protocol The statement that IBGP is preferred over EBGP for ADVPN because IBGP preserves next hop information (D) is true. In a typical ADVPN deployment, it's beneficial to maintain next hop information across the network to ensure proper routing and optimal path selection. Reference: This understanding comes from my knowledge of Fortinet's SD-WAN and ADVPN configurations, where BGP's behavior in terms of next hop preservation is a key consideration.
NEW QUESTION # 25
Refer to the exhibit.
The exhibit shows the BGP configuration on the hub in a hub-and-spoke topology. The administrator wants BGP to advertise prefixes from spokes to other spokes over the IPsec overlays, including additional paths.
However, when looking at the spoke routing table, the administrator does not see the prefixes from other spokes and the additional paths.
Based on the exhibit, which three settings must the administrator configure inside each BGP neighbor group so spokes can learn other spokes prefixes and their additional paths? (Choose three.)
- A. Enable soft-reconfiguration
- B. Set adv-additional-path to the number of additional paths to advertise
- C. Enable route-reflector-client
- D. Set advertisement-interval to the number of additional paths to advertise
- E. Set additional-path to send
Answer: B,C,E
NEW QUESTION # 26
Refer to the exhibit.
Which configuration change is required if the responder FortiGate uses a dynamic routing protocol to
exchange routes over IPsec?
- A. mode-cfg must be enabled.
- B. add-route must be disabled.
- C. exchange-interface-ip must be enabled.
- D. type must be set to static.
Answer: B
NEW QUESTION # 27
Refer to the exhibit.
FortiGate has multiple dial-up VPN interfaces incoming on port1 that match only FIRST_VPN.
Which two configuration changes must be made to both IPsec VPN interfaces to allow incoming connections to match all possible IPsec dial-up interfaces? (Choose two.)
- A. Use different proposals are used between the interfaces.
- B. Configure the IKE mode to be aggressive mode.
- C. Specify a unique peer ID for each dial-up VPN interface.
- D. Use unique Diffie Hellman groups on each VPN interface.
Answer: B,C
NEW QUESTION # 28
Refer to the exhibit.
The device exchanges routes using IBGP.
Which two statements are correct about the IBGP configuration and routing information on the device?
(Choose two.)
- A. Each BGP route is three hops away from the destination.
- B. You can run the get router info routing-table database command to display the additional paths.
- C. ibgp-multipath is disabled.
- D. additional-path is enabled.
Answer: B,D
NEW QUESTION # 29
Which statement about using BGP routes in SD-WAN is true?
- A. You must configure AS path prepending.
- B. Learned routes can be used as dynamic destinations in SD-WAN rules.
- C. You must use external BGP.
- D. You must use BGP to route traffic for both overlay and underlay links.
Answer: B
NEW QUESTION # 30
Refer to the exhibits.
Exhibit A
Exhibit B
Exhibit A shows the source NAT (SNAT) global setting and exhibit B shows the routing table on FortiGate.
Based on the exhibits, which two actions does FortiGate perform on existing sessions established over port2, if the administrator increases the static route priority on port2 to 20? (Choose two.)
- A. FortiGate continues routing the sessions with no SNAT, over port2.
- B. FortiGate performs a route lookup for the original traffic only.
- C. FortiGate updates the gateway information of the sessions with SNAT so that they use port1 instead of port2.
- D. FortiGate flags the sessions as dirty.
Answer: C,D
NEW QUESTION # 31
Which two statements about SD-WAN central management are true? (Choose two.)
- A. It is enabled or disabled on a per-ADOM basis.
- B. It is enabled by default.
- C. It uses templates to configure SD-WAN on managed devices.
- D. It does not allow you to monitor the status of SD-WAN members.
Answer: A,C
NEW QUESTION # 32
Refer to the exhibits.

Exhibit A shows the SD-WAN rule status and the learned BGP routes with community 65000:10.
Exhibit B shows the SD-WAN rule configuration, the BGP neighbor configuration, and the route map configuration.
The administrator wants to steer corporate traffic using routes tags in the SD-WAN rule ID 1.
However, the administrator observes that the corporate traffic does not match the SD-WAN rule ID 1.
Based on the exhibits, which configuration change is required to fix issue?
- A. In SD-WAN rule ID 1, change the destination to use ISDB entries.
- B. In the BGP neighbor configuration, apply the route map dcl-lab-rm in the outbound direction.
- C. In the dcl-lab-rm route map configuration, set set-route-tag to 10.
- D. In the dcl-lab-rm route map configuration, unset match-community.
Answer: B
NEW QUESTION # 33
Refer to the exhibit.
The device exchanges routes using IBGP.
Which two statements are correct about the IBGP configuration and routing information on the device? (Choose two.)
- A. Each BGP route is three hops away from the destination.
- B. You can run the get router info routing-table database command to display the additional paths.
- C. ibgp-multipath is disabled.
- D. additional-path is enabled.
Answer: B,D
NEW QUESTION # 34
What three characteristics apply to provisioning templates available on FortiManager? (Choose three.)
- A. Templates are applied in order, from top to bottom.
- B. A template group can contain CLI templates of both types.
- C. A CLI template can be of type CLI script or Perl script.
- D. You can apply a system template and a CLI template to the same FortiGate device.
- E. A template group can include a system template and an SD-WAN template.
Answer: A,B,C
Explanation:
According to the FortiManager Administration Guide, provisioning templates are used to configure FortiGate devices in a consistent and efficient way. There are different types of templates, such as system, IPsec, SD-WAN, certificate, and CLI templates. Some characteristics of provisioning templates are:
You can apply a system template and a CLI template to the same FortiGate device, as long as they do not have conflicting settings1.
A CLI template can be of type CLI script or Perl script. A CLI script template contains FortiOS CLI commands, while a Perl script template contains Perl code that can generate FortiOS CLI commands2.
A template group can include a system template and an SD-WAN template, as well as other types of templates. A template group is a collection of templates that can be applied to multiple devices at once3.
A template group can contain CLI templates of both types, as long as they do not have conflicting settings2.
Templates are applied in order, from top to bottom. The order of the templates in a template group determines the order in which they are applied to the devices3.
NEW QUESTION # 35
Refer to the exhibits.
Exhibit A -
Exhibit B -
Exhibit A shows a site-to-site topology between two FortiGate devices: branch1_fgt and dc1_fgt. Exhibit B shows the system global and system settings configuration on dc1_fgt.
When branch1_client establishes a connection to dc1_host, the administrator observes that, on dc1_fgt, the reply traffic is routed over T_INET_0_0, even though T_INET_1_0 is the preferred member in the matching SD-WAN rule.
Based on the information shown in the exhibits, what configuration change must be made on dc1_fgt so dc1_fgt routes the reply traffic over T_INET_1_0?
- A. Disable t#p-session-without-syn under config system settings.
- B. Enable snat-route-change under config system global.
- C. Disable allow-subnet-overlap under config system settings.
- D. Enable auxiliary-session under config system settings.
Answer: D
NEW QUESTION # 36
......
Fortinet NSE7_SDW-7.2 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
| Topic 5 |
|
PDF Download Fortinet Test To Gain Brilliante Result!: https://www.dumpsmaterials.com/NSE7_SDW-7.2-real-torrent.html
Get Special Discount Offer on NSE7_SDW-7.2 Dumps PDF: https://drive.google.com/open?id=1xYEWT7ABWiklVP5ivEHrcJZsu2INPiTE
