Free 2023 Ericsson Certified Associate ECP-206 dumps are available on Google Drive shared by DumpsMaterials
Welcome to download the newest DumpsMaterials ECP-206 PDF dumps: https://www.dumpsmaterials.com/ECP-206-real-torrent.html ( 62 Q&As)
NEW QUESTION # 10
What does an LDP implicit null label cause?
- A. penultimate hop popping by an upstream router
- B. forwarding the packet unchanged
- C. swapping with a new label
- D. penultimate hop popping by a downstream router
Answer: D
Explanation:
Explanation
An LDP implicit null label causes penultimate hop popping by a downstream router. LDP is a protocol that distributes labels for MPLS forwarding along the shortest path calculated by an IGP. An implicit null label is a special label value of 3 that indicates that the downstream router does not need a label to forward the packet to its destination. When an upstream router receives an implicit null label from a downstream router, it removes (or pops) the label from the packet before sending it to the downstream router. This process is called penultimate hop popping (PHP) and it reduces the load on the downstream router, which can forward the packet based on its IP header or another label in the stack59.
References: MPLS Label Distribution Protocol Commands - Cisco, Solved: Implicit null and Explicit null - Cisco Community
NEW QUESTION # 11
Which two statements are true about link-state routing protocols? (Choose two.)
- A. Each router uses a reliable update mechanism to exchange topology information with its neighbors.
C Link-state routing protocols mainly use hop-counts to determine the link cost - B. A distance vector algorithm is very processor intensive compared to Dijkstra's algorithm.
- C. The advertisement exchange is mainly triggered by a change in the network.
Answer: A,C
Explanation:
Explanation
Link-state routing protocols are one of the two main classes of routing protocols used in packet switching networks for computer communications, the other being distance-vector routing protocols. Examples of link-state routing protocols include Open Shortest Path First (OSPF) and Intermediate System to Intermediate System (IS-IS). The basic concept of link-state routing is that every node constructs a map of the connectivity to the network, in the form of a graph, showing which nodes are connected to which other nodes. Each node then independently calculates the next best logical path from it to every possible destination in the network.
Each collection of best paths will then form each node's routing table.
Two statements that are true about link-state routing protocols are:
The advertisement exchange is mainly triggered by a change in the network. Link-state routing protocols use a flooding mechanism to distribute information about the network topology to all routers in the same area or domain. This information is encapsulated in link-state packets (LSPs) or link-state advertisements (LSAs), which contain information about the router, its directly connected links, and the state of those links. LSPs or LSAs are sent only when there is a change in the topology, such as a link failure or recovery, or when a periodic refresh timer expires. This way, link-state routing protocols can quickly adapt to network changes and maintain an accurate and consistent view of the network.
Each router uses a reliable update mechanism to exchange topology information with its neighbors.
Link-state routing protocols use a reliable update mechanism to ensure that all routers receive and acknowledge the LSPs or LSAs sent by their neighbors. This mechanism involves sending hello messages to establish and maintain adjacencies with neighbors, sending acknowledgment messages to confirm the receipt of LSPs or LSAs, and requesting missing or outdated LSPs or LSAs from neighbors.
This mechanism ensures that all routers have a synchronized database of LSPs or LSAs, which is used to build a complete network connectivity map and to calculate the shortest path to destinations.
References: Link-state routing protocol - Wikipedia, Ericsson IP Networking - Routing Protocols
NEW QUESTION # 12
Which conceptual table created by routing protocols is used when processing an IP packet?
- A. management information base
- B. label information base
- C. forwarding information base
- D. traffic engineering data base
Answer: C
Explanation:
Explanation
The conceptual table created by routing protocols that is used when processing an IP packet is the forwarding information base (FIB). The FIB is a table that contains the bestroutes to reach each destination network prefix, along with the outgoing interface and the next-hop address for each route. The FIB is derived from the routing information base (RIB), which is a table that contains all the routes learned from different routing protocols and sources. The FIB is used by the router to make fast forwarding decisions for each incoming packet, based on its destination address12.
References: Security Hardening Checklist Guide for Cisco Routers/Switches in 10 Steps, VLAN - Wikipedia
NEW QUESTION # 13
In your network, video traffic is being marked with DSCP code AF31.
Based on industry standard practice, which code would you use to assign higher priority to VoIP traffic?
- A. AF21
- B. DF
- C. AF11
- D. EF
Answer: D
Explanation:
Explanation
The code that is commonly used to assign higher priority to VoIP traffic is EF, which stands for Expedited Forwarding. EF is a per-hop behavior (PHB) defined by the Differentiated Services (DiffServ) model for QoS.
EF provides low delay, low jitter, and low loss for real-time applications such as VoIP. EF is marked by setting the DSCP value to 101110, which corresponds to decimal 4678. AF31, which stands for Assured Forwarding class 3 low drop probability, is another PHB defined by DiffServ, but it provides lower priority than EF. AF31 is marked by setting the DSCP value to 011010, which corresponds to decimal 2678. DF, which stands for Default Forwarding, is a PHB defined by DiffServ that provides best-effort service for unmarked traffic. DF is marked by setting the DSCP value to 000000, which corresponds to decimal 078.
AF11, which stands for Assured Forwarding class 1 low drop probability, is another PHB defined by DiffServ, but it provides lower priority than EF and AF31. AF11 is marked by setting the DSCP value to 001010, which corresponds to decimal 1078.
References: Differentiated services - Wikipedia, Solved: Cisco VoIP Phone traffic marking - Cisco Community
NEW QUESTION # 14
Which protocol would be used to bundle multiple Ethernet ports into a virtual link with an aggregated bandwidth?
- A. VRRP
- B. LACP
- C. ERP
- D. RSTP
Answer: B
Explanation:
Explanation
The protocol that would be used to bundle multiple Ethernet ports into a virtual link with an aggregated bandwidth is LACP, which stands for Link Aggregation Control Protocol. LACP is a protocol that allows two or more devices to negotiate the formation of a link aggregation group (LAG), also known as an EtherChannel or a port channel. A LAG combines multiple physical links into one logical link that provides increased bandwidth, load balancing, and redundancy. LACP is defined in IEEE 802.3ad and 802.1AX standards12.
References: Link Aggregation Control Protocol - Wikipedia, What is "link aggregation" and how does it benefit your network? | PC Gamer
NEW QUESTION # 15
What network information is, without additional configuration, shared between two iBGP neighbors by default?
- A. BGP routes learned from an OSPF neighbor
- B. IP address information of loopback interfaces
- C. IP address information from all directly connected interfaces
- D. BGP routes learned from eBGP neighbors
Answer: D
Explanation:
Explanation
iBGP works by exchanging routing information between two or more routers within an AS. Each router sends its own routing table to its neighbors, which contains information about the networks it knows and how they can be reached from that router. By default, iBGP neighbors only share BGP routes learned from eBGP neighbors, which are routers in different ASes. This is because iBGP assumes that all routers within an AS have consistent internal routing information provided by an IGP, such as OSPF or IS-IS. Therefore, iBGP neighbors do not need to share IP address information of loopbackinterfaces or directly connected interfaces, unless explicitly configured to do so by using commands such as neighbor update-source or network.
References: iBGP Ultimate Guide | How iBGP Is Different From eBGP, Ericsson IP Networking - Routing Protocols
NEW QUESTION # 16
What is used for Ethernet loop avoidance?
- A. Time-to-Live (TTL)
- B. Split-Horizon
- C. Poison-Reverse
- D. Spanning-Tree
Answer: D
Explanation:
Explanation
Spanning-Tree is used for Ethernet loop avoidance. Spanning-Tree is a protocol that prevents loops in Ethernet networks by creating a logical tree topology of the network switches. Spanning-Tree blocks some of the redundant links between switches to ensure that there is only one active path between any two nodes in thenetwork. Spanning-Tree also detects and recovers from link failures by activating alternative paths when needed56.
References: Network loops and loop avoidance - Medium, Spanning Tree Protocol - Wikipedia
NEW QUESTION # 17
Which two statements are true regarding the LSP? (Choose two.)
- A. The LSP refers to a specific label assigned to a packet by the LSR for a destination.
- B. The LSP refers to a sequence of routers that forward the MPLS packet based on labels.
- C. The LSP refers to a sequence of routers that add. remove, or change label values along the path.
- D. The LSP refers to a sequence of routers that add, remove, or change label values based on the destination MAC address.
Answer: B,C
Explanation:
Explanation
Two statements that are true regarding the LSP are:
The LSP refers to a sequence of routers that forward the MPLS packet based on labels. An LSP is a Label Switched Path, which is a path through an MPLS network that is established by signaling protocols such as LDP or RSVP-TE. An LSP consists of a sequence of routers (called Label Switching Routers or LSRs) that forward packets based on labels rather than IP addresses. Labels are short fixed-length identifiers that are attached to packets at the ingress router and removed at the egress router. Labels can be swapped or popped at intermediate routers according to their label forwarding tables78.
The LSP refers to a sequence of routers that add, remove, or change label values along the path. As mentioned above, an LSP consists of a sequence of routers that forward packets based on labels. Along the path, different routers may perform different operations on the labels depending on their role and configuration. The ingress router adds one or more labels to the packet before sending it into the MPLS network. The egress router removes all labels from the packet before sending it out of the MPLS network. The intermediate routers may swap one label with another label according to their label forwarding tables. This process is called label switching78.
References: MPLS Fundamentals: 3 - MPLS Packet Forwarding, Multiprotocol Label Switching - Wikipedia
NEW QUESTION # 18
Which operating system is used in Ericsson Router 6000 products?
- A. IPOS
- B. ERS
- C. SE-OS
- D. ERS
- E. Junos
Answer: D
Explanation:
Explanation
The operating system used in Ericsson Router 6000 products is ERS (Ericsson Router Software). ERS is based on IPOS (IP Operating System), which is a common operating system for Ericsson's IP portfolio. ERS provides advanced features and functionality for IP transport, such as MPLS, Segment Routing, QoS, IPSec, synchronization, SDN, and more. ERS also supports seamless integration with Ericsson Radio System and Ericsson Network Manager.
References: Router 6000 Series - Ericsson, Router 6675 Datasheet - Winncom
NEW QUESTION # 19
Which two statements are true about the Ericsson Router 6000 series? (Choose two.)
- A. The Router 6000 products range from all-outdoor small site routers to large aggregation routers.
- B. The Router 6000 can host containerized applications such as firewalls.
- C. The Router 6000 uses the same building practice and accessories as the Ericsson Radio System.
- D. The Router 6000 is solely built as a radio cell site router.
Answer: A,C
Explanation:
Explanation
Two statements that are true about the Ericsson Router 6000 series are:
The Router 6000 uses the same building practice and accessories as the Ericsson Radio System. The Ericsson Radio System is a modular and scalableradio access network solution that supports multiple standards, bands, and layers. The Router 6000 series is fully integrated into the Ericsson Radio System, using the same building practice and accessories such as mounting kits, cables, power supplies, etc. This simplifies installation, operation, and maintenance of both radio and transport equipment78.
The Router 6000 products range from all-outdoor small site routers to large aggregation routers. The Router 6000 series consists of three main products: the Router 6672 for access, the Router 6675 for pre-aggregation, and the Router 6274 for metro aggregation. The Router 6672 is an all-outdoor small cell site router with high-capacity and low-power consumption. The Router 6675 is a combined access and E-RAN switch with hardware-accelerated IPSec and high-accuracy internal clock. The Router 6274 is a high-capacity metro aggregation router with SDN functionality and flexible interface options78.
References: Router 6000 Series - Ericsson, New Ericsson Router 6000 series couples radio and IP transport for 5G future - Global Brands Magazine
NEW QUESTION # 20
What is an important difference between OSPF and IS-IS?
- A. OSPF runs directly on IP, while IS-IS runs directly on Ethernet.
- B. OSPF runs directly on Ethernet, while IS-IS runs directly on IP.
- C. OSPF is a link state protocol, while IS-IS is a distance vector protocol.
- D. OSPF is a distance vector protocol, while IS-IS is a link state protocol.
Answer: A
Explanation:
Explanation
OSPF runs directly on IP, while IS-IS runs directly on Ethernet. This means that OSPF uses IP addresses to identify routers and links, while IS-IS uses MAC addresses or other link-layer identifiers. OSPF also requires an IP header for each packet, while IS-IS does not. Both OSPF and IS-IS are link state protocols, which means that they flood information about the network topology to all routers in the same area or domain. References: Ericsson IP Networking - Routing Protocols, Ericsson Router 6000 Series - Ericsson
NEW QUESTION # 21
What is a reason for using VLANs in an IP network?
- A. to isolate hosts across multiple IP subnets
- B. to implement virtual routing
- C. to isolate hosts within the same IP subnet
- D. to enable MAC address learning on a router port
Answer: C
Explanation:
Explanation
A reason for using VLANs in an IP network is to isolate hosts within the same IP subnet. VLANs (Virtual LANs) are logical grouping of devices in the same broadcast domain. VLANs are usually configured on switches by placing some interfaces into one broadcast domain and some interfaces into another. Each VLAN acts as a subgroup of the switch ports in an Ethernet LAN. VLANs allow network administrators to group hosts together even if the hosts are not directly connected to the same network switch. By using VLANs, hosts within the same IP subnet can be separated into different broadcast domains, which enhances security, reduces network congestion, and simplifies network management78.
References: 8 Different Types of VLANs in TCP/IP Networks, What is a VLAN? - Study-CCNA
NEW QUESTION # 22
What are two roles of the DHCP protocol in a network? (Choose two.)
- A. It is used by hosts to obtain the IP address and other parameters from the DHCP server.
- B. It is used to inform hosts about the default gateway.
- C. It provides information about the number of hops between the source and the destination.
- D. It provides the authorization function to the network.
Answer: A,B
Explanation:
Explanation
Two roles of the DHCP protocol in a network are:
It is used by hosts to obtain the IP address and other parameters from the DHCP server. DHCP stands for Dynamic Host Configuration Protocol, which is a protocol that provides automatic and centralized management of IP addresses and other network configuration parameters for devices connected to a network. A host that needs an IP address can send a request to a DHCP server, which will assign an available IP address from a pool and lease it to the host for a certain period of time34.
It is used to inform hosts about the default gateway. The default gateway is the IP address of the router that connects the host to other networks. The default gateway is one of the parameters that can be delivered by the DHCP server to the host, along with other parameters such as subnet mask, DNS server, domain name, etc. The host can use the default gateway to send packets to destinations outside of its local network34.
References: What Is DHCP? (Dynamic Host Configuration Protocol) - Lifewire, Dynamic Host Configuration Protocol - Wikipedia
NEW QUESTION # 23
Which statement is true about LDP?
- A. LDP and IGP both exchange their databases every 30 seconds.
- B. LDP and IGP both exchange their databases every 60 seconds.
- C. LDP performs routing functions along with IGP.
- D. LDP relies on IGP for all routing-related decisions.
Answer: D
Explanation:
Explanation
LDP relies on IGP for all routing-related decisions. LDP is a protocol that distributes labels in an MPLS environment, but it does not perform any routing functions. LDP uses the underlying routing information provided by an IGP, such as OSPF or IS-IS, to forward label packets. LDP and IGP do not exchange their databases at regular intervals, but rather use hello messages to maintain adjacencies and sessions. References: Ericsson IP Networking - Routing Protocols, Label Distribution Protocol - Wikipedia
NEW QUESTION # 24
What is the CLI command to obtain the software version in Ericsson Router 6000 products?
- A. show sysstat
- B. show version
- C. show log
- D. show release
Answer: B
Explanation:
Explanation
The CLI command to obtain the software version in Ericsson Router 6000 products is show version. This command displays information about the software release, the hardware model, the serial number, the uptime, and the boot image of the router. References: [ERICSSON SMARTEDGE 600 HARDWARE MANUAL Pdf Download | ManualsLib], Ericsson Router 6000 Series - Ericsson
NEW QUESTION # 25
Which statement accurately defines an Autonomous System (AS)?
- A. An AS is a network that is capable of autonomously forwarding packets, regardless of direct or indirect connectivity to the Internet.
- B. An AS is a set of routers under a single administration, using an interior gateway protocol and common metrics to route packets within the AS.
- C. An AS is a group of networks directly connected to each other that can distribute eBGP information using directly established links.
- D. An AS is a collection of IS-IS routes imported into BGP and presented in such a way that networks connected to the AS have a global overview of the network.
Answer: B
Explanation:
Explanation
The statement that accurately defines an Autonomous System (AS) is that an AS is a set of routers under a single administration, using an interior gateway protocol and common metrics to route packets within the AS.
An AS is a logical grouping of networks that share a common routing policy and operate under a single administrative authority. An AS can be a single network or a collection of networks that are interconnected by routers. An AS uses an interior gateway protocol (IGP), such as OSPF or IS-IS, to exchange routing information within the AS. An IGP uses common metrics, such as hop count or bandwidth, to determine the best path to each destination within the AS. An AS also has a unique number assigned by IANA, called an AS number (ASN), which identifies the AS in interdomain routing .
References: [Autonomous system (Internet) - Wikipedia], [What Is an Autonomous System? - Cisco]
NEW QUESTION # 26
Review the exhibit.
In the exhibit, which action is performed by router R4?
- A. PHP
- B. pop
- C. swap
- D. push
Answer: C
Explanation:
Explanation
In the exhibit, router R4 is performing a swap action. This means that router R4 is replacing the incoming label with a new label and forwarding the packet to the next hop along the LSP. In this case, router R4 receives a packet with label 20 from router R3 and swaps it with label 30 before sending it to router R5.
The exhibit shows an example of an MPLS network with four routers: R1, R2, R3, and R4. Router R1 is the ingress PE router and router R4 is the egress PE router. Router R2 and R3 are P routers. Router R1 assigns label 10 to the packet and sends it to router R2. Router R2 swaps label 10 with label 20 and sends it to router R3. Router R3 swaps label 20 with label 30 and sends it to router R4. Router R4 removes label 30 from the packet and forwards it based on its IP header or another label in the stack.
Therefore, the answer is D.
References: MPLS Label Switching | MPLS Operation | Push, Swap,Push IPCisco, A Complete Guide to Multiprotocol Label Switching (MPLS) - G2, Multiprotocol Label Switching - Wikipedia
NEW QUESTION # 27
Which two protocols apply to both IPv4 and IPv6? (Choose two.)
- A. ARP
- B. MD
- C. DNS
- D. SNMP
Answer: C,D
Explanation:
Explanation
Two protocols that apply to both IPv4 and IPv6 are:
SNMP: This stands for Simple Network Management Protocol, which is a protocol that allows network administrators to monitor and manage network devices such as routers, switches, servers, printers, etc.
SNMP uses a client-server model, where an SNMP manager (client) can query or configure an SNMP agent (server) on a network device using SNMP messages. SNMP can operate over both IPv4 and IPv6 networks56.
DNS: This stands for Domain Name System, which is a protocol that translates human-readable domain names (such as www.example.com) into numerical IPaddresses (such as 192.0.2.1 or 2001:db8::1) that identify network devices. DNS uses a hierarchical distributed database of name servers that store and resolve domain names and IP addresses. DNS can support both IPv4 and IPv6 addresses78.
References: Simple Network Management Protocol - Wikipedia, SNMP over IPv6 - Cisco, Domain Name System - Wikipedia, DNS for IPv6 - Cisco
NEW QUESTION # 28
An operator wants to ensure that they can differentiate their traffic types for the purpose of prioritization in their Ethernet LAN and IP/MPLS backbone.
Which three fields would be used? (Choose three.)
- A. PCP
- B. DSCP
- C. VID
- D. ECN
- E. Traffic Class (TC)
Answer: A,B,E
Explanation:
Explanation
To differentiate traffic types for the purpose of prioritization in their Ethernet LAN and IP/MPLS backbone, an operator can use the following three fields:
Traffic Class (TC): This is a 3-bit field in the MPLS label that can be used to indicate the priority or class of service (CoS) of the packet. The TC field can be mapped to the DSCP field in the IP header or the PCP field in the Ethernet header. The TC field can be used by MPLS routers to apply different per-hop behaviors (PHBs) such as queuing, scheduling, and dropping policies to different traffic classes12.
DSCP: This is a 6-bit field in the IP header that can be used to mark packets according to the differentiated services (DiffServ) model. The DSCP field can indicate the per-hop behavior (PHB) that the packet should receive at each router along its path. The DSCP field can be mapped to the TC field in the MPLS label or the PCP field in the Ethernet header. The DSCP field can be used by IP routers to provide QoS for different traffic types34.
PCP: This is a 3-bit field in the Ethernet header that can be used to mark packets according to the IEEE
802.1Q standard. The PCP field can indicate the priority or class of service (CoS) of the packet on an Ethernet LAN. The PCP field can be mapped to the TC field in the MPLS label or the DSCP field in the IP header. The PCP field can be used by Ethernet switches to provide QoS for different traffic types56.
References: MPLS Traffic Engineering - DiffServ-Aware Traffic Engineering, MPLS Traffic Engineering - DiffServ-Aware Traffic Engineering Configuration Guide, Differentiated services - Wikipedia, DSCP and Precedence Values - Cisco, 802.1Q VLAN IDs and Ethernet Interface Types - Juniper Networks, Introduction to Virtual LANs (VLANs) and Tagging - Ubiquiti Support and Help Center
NEW QUESTION # 29
......
Tested Material Used To ECP-206: https://www.dumpsmaterials.com/ECP-206-real-torrent.html
Following are some new ECP-206 Real Exam Questions!: https://drive.google.com/open?id=1mZ4P72vLqKYAjlheX_4X3ikHsaN9ZwGt
